Makita MAC210Q Quiet Series review
A jobsite-grade quiet compressor with a full roll cage, 135 PSI max and a 60 dB rating. It costs more than the California Air Tools 2010A but is built to be thrown in a truck. At 60 dB it is about as loud as a normal conversation.
Affiliate link · we may earn a commission · Affiliate disclosure
How loud is it?
- Makita MAC210Q Quiet Series60 dB
Manufacturer rating, measuring distance not stated. Brands measure at different distances, so treat 1–2 dB differences as a tie. Why dB ratings vary.
Full specifications
| Noise rating | 60 dB |
|---|---|
| Noise source | Manufacturer rating, measuring distance not stated |
| CFM at 90 PSI | 2 |
| CFM at 40 PSI | 3 |
| Max PSI | 135 |
| Tank | 2 gal |
| Horsepower | 1 HP |
| Pump | Oil-free |
| Stages | — |
| Power | 120V outlet |
| Duty cycle | — |
| Weight | 45.2 lb |
| Price band | $300–$600 (checked October 18, 2026) |
A dash means the manufacturer doesn't publish that figure. We never estimate one.
Our take
Makita's Quiet Series targets pros working inside finished homes. The MAC210Q runs its oil-free dual-piston pump at 1,750 RPM and carries a 60 dB rating, so it sits in the same noise class as California Air Tools while adding a full steel roll cage.
Makita rates it at 2.0 CFM at 90 PSI and 3.0 CFM at 40 PSI, with a higher 135 PSI cut-out than most quiet compressors. A higher cut-out stores more usable air in the 2-gallon tank, so you get more nails between cycles.
Buyers are enthusiastic about how quiet it is, and several mention it runs a nailer at 90 PSI without falling behind. The main complaint is weight: at roughly 45 lb it is heavier than the spec sheet suggests. If you work inside occupied houses every day, the extra durability is worth paying for.
Pros
- Full roll-cage frame protects the pump and gauges
- 135 PSI max stores more air per gallon
- Low 1,750 RPM motor for longer life
Cons
- Heavier than it looks at about 45 lb
- Pricier than similar-output quiet compressors
What it can run
With a 30% safety margin, 2 CFM at 90 PSI comfortably covers these tools from our list (nailers assumed at 30 shots a minute):
- Metabo HPT NT50AE2 18-Gauge Brad Nailer (0.025 cu ft per shot)
Who it's for, and who should skip it
Best for: Jobsite trim crews that need a quiet, tough compressor.
Buy it if: you work indoors or near people and want conversation-level noise; your main jobs are nailing, inflation and blow-off; you want a pump with no oil to change.
Skip it if: you plan to run impact wrenches, sanders or spray guns for long.
How it compares in its class
- Ranked #5 of 12 in best quiet air compressors.
- Quieter than 5 of the 11 other rated models in that list.
- 2 CFM at 90 PSI against a class median of 2.3 CFM, so below average airflow for the class.
- Price band $300–$600; see every spec side by side in the comparison table.
Ownership tips
- Drain the tank after each use (daily on a shop compressor) to stop rust from the inside.
- The pump is oil-free, so there's no oil to change; keep the intake filter clean instead.
- Plug it straight into a wall outlet and use a longer air hose instead of a long, thin extension cord.
- Test the safety relief valve now and then by pulling its ring briefly, and never adjust or plug it.
General guidance; always follow the owner's manual. More in our maintenance checklist.
Makita MAC210Q Quiet Series: quick answers
How loud is the Makita MAC210Q Quiet Series?
It is rated at 60 dB (manufacturer rating, measuring distance not stated), which is about as loud as a normal conversation.
What can the Makita MAC210Q Quiet Series run?
With a 30% safety margin it covers Metabo HPT NT50AE2 18-Gauge Brad Nailer from our tool list, based on 2 CFM at 90 PSI.
Is the Makita MAC210Q Quiet Series oil-free?
Yes. The pump is oil-free, so there's no oil to check or change.
What power does the Makita MAC210Q Quiet Series need?
It runs from a standard 120V household outlet. For larger units, a dedicated 20A circuit is best; avoid long, thin extension cords.
Spec sources
Where each figure on this page comes from (checked October 18, 2026). We don't present manufacturer figures as our own measurements.
- Amazon product listing: noise, max PSI, tank, horsepower, pump type
- homedepot.com: CFM @ 90 PSI, CFM @ 40 PSI, weight
Alternatives to consider
California Air Tools 8010A
60 dB · 2.2 CFM @ 90 PSI · $150–$300
Quiet home garage with more stored air
Makita MAC320Q Quiet Series
60 dB · 2.6 CFM @ 90 PSI · $300–$600
The most airflow you can get at 60 dB
Appears in: Best quiet air compressors · Ultra quiet (≤60 dB) · Oil-free · Portable